Ads code here

Media Center Out of Pallets

Do not forget! follow DIYSelfy on facebook to get new and fresh ideas and updates everyday!

It is actually a fairly easy project, as long as you are comfortable using a circular skill saw. While it may be pretty straight forward, it does take some time because of all the different steps involved and waiting time.


Supplies Needed:

– Pallets- Find ones that are the exact same length and have the same number of boards across
– 5/4″X 4 X 10″ boards (1 per pallet)
– Electric Sander and 200 grit paper
– Foaming Glue
– Dark Walnut Stain
– Satin Polycrylic Sealer
– Galvanized Fencing Nails
– 2″ Metal Hinges
– Mask to help with the fumes

These are the pallets that I started with. I chose this style because the boards were evenly placed across the pallet and they were all in tact. For this project, it is extremely helpful to use pallets that are exactly the same size, this way they will fit together senselessly and the end result will look more polished.


Start by removing all of the staples and debris attached to the pallets.

Then cut the pallet in half, horizontally. My pallets had exactly 6 boards across, so I cut straight down the middle so there were three boards on each side.

Flip the pallets over and remove the two boards attached to the underside.


Now you should have two pieces exactly alike.


Take your 5/4 X 10 X 4 boards and cut them to fit the length of your pallet. These boards will be used to make the pallet taller.  Mine measured 19 1/4″ long.


Place a thin line of glue on top of the boards that are already sticking up from the pallets, and then place one 5/4″ X 4 X 19 1/4 ” boards on top of each board. Press gently to secure them.

When placing the boards on top, make sure to align them with the ‘good’ side of the pallet. Meaning, the side that was not cut with the saw. This will be the ‘front facing’ part of the cube system and they will be nice and even. We’ll trim the back in a few steps.

Wait about an hour for the first layer to dry.


Place another layer of glue onto the boards, then add another set of 5/4″ X 4 ” 19 1/4″ boards. Apply another layer of glue, then place the second pallet section on top, creating your cube system. I placed two layers of boards in between the pallets in order to fit the square baskets I was using. But if you wanted to use smaller baskets you could remove a layer of boards.

You may notice in the picture the foaming glue seeping out between the boards. I used an X-Acto Knife to trim away the glue when this happened. Just wait for it to dry first.

One unit measures 19 1/4″ deep, 32″ across and 14 1/2 ” high.


This is what the ‘back’ or ‘rear-facing’ side of the pallet will look like. We all know pallets are rustic and not perfect, and I’m sure my cuts aren’t perfect either. So,  I used the Skill Saw to trim this section the best I could.


Next, using an electric sander, sand down every crevice of your pallets. The more you sand the better the stain will take to the wood. I sanded the top, bottom, inside each cubby, etc. I didn’t over do it, but definitely spent some time smoothing out the wood and removing any splinters or bad spots.


Now we are getting to the fun part, choosing your stain. I knew I wanted mine a dark stain so I chose a few samples and tested them out on the wood. Always remember to test out the stain first because each stain will take differently to different types of wood. Even the same color in a different brand will look different.

You can apply the stain using either a brush or a soft rag (like from an old t-shirt). I prefer to use a rag, I think it applies a little more evenly. Now, for this project I only used one coat of stain and didn’t worry about making it perfect. I wanted these to have more of a rustic look so I wasn’t worried if there were spots that were uneven or not completely covered.


Allow the stain to dry overnight and then apply a few layers of Polycrylic sealer. I used a clear satin sheen to help keep its rustic look.

Note: Because of how large my ‘media center’ turned out, I ended up purchasing about five 32 oz cans of both stain and sealer.


After the pallets were dry, I stacked two on top of each other across the entire wall and filled them with square wicker baskets. My pallet units fit almost perfectly across the room.



Lastly, once the pallets were in place I added the hardware for both a decorative and functional purpose.


via designdininganddiapers

Δημοσίευση σχολίου